How to Reset Your Motherboard

Are you having trouble with your computer? It might be because of a problem with your motherboard. This article will show you how to reset your motherboard and fix the problem.

If you are having trouble with your computer, it might be because of a problem with your motherboard. The motherboard is the main circuit board in your computer, and it controls everything from the power to the data. If there is a problem with the motherboard, it can cause your computer to crash or freeze.

BIOS

Your computer’s Basic Input Output System, or BIOS, is a crucial piece of software that starts up your machine and helps control its essential functions. When you turn on your computer, the BIOS loads into memory and begins running. It initializes the hardware, checks for errors, and starts the boot process. The BIOS also provides a set of low-level commands that you can use to manage your hard drive, keyboard, mouse, and other devices.

CMOS

CMOS is short for Complimentary Metal Oxide Semiconductor. CMOS is a technology used in microprocessors and microcontrollers. The term “reset” usually refers to a hard reset, which clears all the program memory, registers, and flags in the processor. This type of reset is also known as a power-on reset.

Resetting of BIOS

There are essentially three ways to reset your Motherboard:

  1. Resetting the BIOS Internally
  2. Resetting CMOS by Removing the CMOS Battery
  3. Resetting CMOS Through the Clear CMOS Jumpers

Resetting the BIOS Internally

The BIOS holds critical information about the system, including settings for the hard disk, memory, processor, and other devices. It also contains information on how to load operating systems and applications. The BIOS is stored in a flash R.O.M. chip on the Motherboard. The BIOS is read by a program called an “EPROM” (erasable programmable read-only memory) that holds the information.

This is one of the least intrusive and most straightforward ways to understand if you require the more intricate procedures explained here.

You will need to restart your computer to enter its BIOS. The key you need to press will probably be F2 and F12.

As a computer restarts, quickly press on the specific key you identified earlier when you see the first logo. You will have a short period to do this.

After entering your computer’s BIOS, the place to go to inspect a setting’s default location is Setup Defaults or something similar like Load Default Configuration. Shut down the settings in your BIOS and finally reboot the system.

Resetting CMOS by Removing the CMOS Battery

One way to do this is to remove the CMOS battery. This is located on the Motherboard, underneath its cover. Please remove the battery by gently lifting it out of its hole and replacing it with a new one.

First, you disconnect the power supply of your computer. Find the battery on your Motherboard. Please remove the battery from its slot. Insert the battery back into the place after a couple of minutes.

Reconnect the power cable to your Motherboard, and then restart your computer. Handle both positive and negative terminals of the battery. After removing the battery of your Motherboard, the time and date will reset, and make sure to correct them.

Resetting CMOS Through the Clear CMOS Jumpers

Jumpers are small rings of wire on the Motherboard. For instance, jumpers can connect the laptop to the mains, motherboard speakers to mains power, and the front computer case for lights.

Using the jumper settings on the Motherboard, you can reset the CMOS. This is sometimes done as a one-time fix or to clear any problems with your computer or system at the next boot up. Sometimes, it’s also used to prevent a system crash after a power loss.

First, disconnect the power supply, then you can find out the jumpers. Be aware there is no one sort of CMOS jumper. It’s essential to refer to the Motherboard’s manual to get a clearer idea of where there is a jumper with three pins.

Just take a fine-line screwdriver, and place it so that it contacts both polarity poles at the same time. Keep holding it for a few minutes. It is ideal to use jumper blocks from time holding, but a screwdriver will work fine if you don’t already have a spare jumper block.

You will know if your Motherboard has been restored to default settings if the Time and Date displayed on your personal computer when it restarts also return to default values.

Frequently Asked Questions

Where do I go to find more information on the jumper settings for my specific Motherboard?

There are a few different places you can look for information on jumper settings for your Motherboard. The first place to check is the Motherboard’s manual. If you don’t have the manual, you can usually find it online by searching for the model number of your Motherboard. Another place to check is the manufacturer’s website for your Motherboard. They may have more detailed information on specific jumper settings. Finally, you can also search for forums or articles online that discuss your specific motherboard model.

Which CMOS jumper setting should I use on my Motherboard?

There are a few different jumper settings that you can use on your Motherboard, depending on the type of Motherboard that you have. You can usually find the jumper settings for your Motherboard in the Motherboard’s manual.

John
John is a tech writer who specializes in laptop and PC hardware. He has been writing about technology for over 3 years, and his work has been featured in major publications such as Thrive Global.